About UST Research

Contact us

UST Products

UST Offers

Test Equipment

Free Classifieds


Namecheap.com - Cheap domain name registration, renewal and transfers - Free SSL Certificates - Web Hosting


InfraRed is a energy radiation with a frequency below our eyes sensitivity, so we can not see it.
Even that we can not "see" sound frequencies, we know that they exist, we can hear them.

Even that we can not see or hear infrared, we can feel it at our skin temperature sensors.
When you approach your hand to fire or warm element, you will "feel" the heat, but you can't see it. You can see the fire because it emits other types of radiation, visible to your eyes, but it also emits lots of infrared that you can only feel in your skin.  

 




At the opposite side of the visible spectrum is the Ultra-Violet, above the blue light. U.V. (for short) is dangerous for life, since it literally destroys cells without immediate alarm.  UV is used to sterilize tools, kill bacteria and germs, and it is responsible for skin cancer.   We have no UV sensor in skin, we can't see UV, so we are totally unprotected from UV. When you are exposed to sun's UV, mostly from 11am to 3pm (UV rays angle enters easily at the Earth atmosphere), your skin is being hit by a massive UV radiation and it leads to all sort of problems. Most severe sun burn is caused more by UV than IR, you will only feel it hours later when your skin will respond to the intense UV attack, red, hot, pain. In real, our body developed the skin's IR sensors as a way to protect ourselves from the immediate danger, the fire, since during all the evolutionary process we were much more exposed to fire (burning bushes, trees, forest) emitting lots of IR, than UV.  As the sun also emits IR, our body always used the IR sensors to indicate sun's intensity, forcing us to look for a shading area, thus, protecting us from dangerous UV.  Later on, tanning at the beach gain a new meaning, sun's heat triggers the skin alarm sensors, but it is ignored and UV is all over your fragile skin.  Ignoring the danger people at the beach think that as hotter the better, well, better for skin cancer.

NOTE:  Eprom erasers use a strong UV light, also known as "germicide lamp". This lamp produces hundreds of times more UV than the sun at noon time, it can erase an eprom memory in minutes, it would take many hours at the sun's light to do the same. Be VERY careful when dealing with those lamps when emitting UV, it can cause SEVERE damage to your eyes or skin, even that the only thing you see is a smooth blue light.  Different from "night club's black light" lamps, UV (germicide lamps) have the bulb made in crystal, regular fluorescent lamps (and the black light ones) use regular glass. Glass is a bad conductor of UV, but crystal is very efficient, this is why germicide lamps uses crystal, so UV can gets out and do its killing work.


 


Infra-Red is interesting, because it is easily generated and doesn't suffer electromagnetic interference, so it is nicely used to communication and control, but it is not perfect, some other light emissions could contains infrared as well, and that can interfere in this communication. The sun is an example, since it radiates a wide spectrum of energy.

Lots of things can generate infrared, anything that radiate heat do it, including out body, lamp, stove, oven, car's engine, car's tires, hot asphalt and rocks, plants, even the hot water at the faucet. 

The massive use of IR LEDs at TV/VCR remote controls and other applications, brought infra-red diodes and transistors (emitter and receivers) at very low cost at the market.

To allow a good communication using infra-red, and avoid those "fake" signals, it is imperative to use a "key" that can tell the receiver what is the real data transmitted and what is generated by the surrounding environment.  As an analogy, looking eye naked to the night sky you can see hundreds of stars, but you can spot easily a far away airplane just by its flashing strobe light, even if that blinking light is dimmer than the stars light.  That strobe light is the "key", the "coding" element that alerts us.

Similar yo the airplane at the night sky, the room where the TV is installed may have hundreds of tinny IR sources, our body, the lamps around, even the hot cup of tea. A way to avoid all those other sources, is generating a key, like the flashing airplane. So, remote controls use to pulsate its infrared in a certain frequency. The IR receiver module at the TV, VCR or stereo "tunes" to this certain frequency and ignores all other IR received. The best frequency for the job is between 30 and 60kHz, the most used is around 36kHz. It works exactly as a radio receiver tunning to a specific station. In this case, the receiver tune to the IR "radio" at 36kHz, and ignores the rest. Your cup of hot tea generates IR, but not at 36kHz, it is flat and plain IR emission, and then, ignored by the TV IR receiver.

So, remote controls use the 36kHz (or around) to transmit information. InfraRed light emitted by IR Diodes is pulsated at 36 thousand times per second, when transmitting logic level "1" and silence for "0".

To generate a 36kHz pulsating infrared is quite easy, more difficult is to receive and identify this frequency. This is why some companies produce infrared receives, that contains the filters, decoding circuits and the output shaper, that delivers a square wave, meaning the existence or not of the 36kHz incoming pulsating infrared.

It means that those 3 dollars small units, have an output pin that goes high (+5V) when there is a pulsating 36kHz infrared in front of it, and zero volts when there is not this radiation.

A square wave of approximately 27uS (microseconds) injected at the base of a transistor, can drive an infrared LED to transmit this pulsating light wave. Upon its presence, the commercial receiver will switch its output to high level (+5V).

If you can turn on and off this frequency at the transmitter, your receiver's output will indicate when the transmitter is on or off.

Those IR demodulators have inverted logic at its output, when a burst of IR is sensed it drives its output to low level, meaning logic level = 1.

The TV, VCR, and Audio equipment manufacturers for long use infra-red at their remote controlers. My first color TV in 1976 used an ultrasound (not infrared) remote control.

To avoid a Philips remote control to change channels in a Panasonic TV, they use different codification at the infrared, even that all of them use basically the same transmitted frequency, from 36 to 50kHz. So, all of them use a different combination of bits or how to code the transmitted data to avoid interference.

Some standards were created. As illustrative material, we will only show one of them, the one used by Philips, even that we can cover the other ones in the future.

Click below for other remote control characteristics:
SONY , HITACHI , NEC , PIONEER , JVC ,
From there, use your browser "BACK" button to return to this page.

First of all, Philips adopted or created the RC5 standard that uses fixed bit length and fixed quantity of bits.

Each time you press a button at the Philips remote control, it sends a train of 14 bits, 1.728ms per bit, the whole train is repeated every 130ms if you keep the button pressed

Each bit is sliced in two halves. The left and right half has opposed levels. If the bit to be transmitted is one (1), its left side is zero while its right side is one. If the bit to be transmitted is zero (0), its left side is one while the right side is zero.


(This is the right logic, reversed from what you can see at the IR receiver output.)

It means that the second half of the bit is actually the same meaning of the bit to be transmitted, as you can see at the shaded blue right side of the bit as on, means bit transmitted = 1.

If you want to measure the correct logic level directly from the Receiver Output, you should measure at the first half of the bit.

The correct interpretation, is that it changes level exactly at the middle of bit time.  At the IR Receiver output a bit Zero changes level from Low to Up, while a bit One changes level from Up to Low.

There are a minimum quantity of incoming 27Еs pulses to the demodulator understand it is at the right frequency and then drop its output.  The quantity of pulses used at the Philips remotes are 32 pulses per each half of the bit, 64 pulses per bit.  So, a bit "0" to be transmitted it means 32 square pulses of  27Еs each, then 32 x  27Еs of silence.  The bit "1" is the opposite, 32 x 27Еs of silence followed by  32 square pulses of  27Еs.

Our job here will be to decode the receiving of the waveform at the demodulator output. We could observe the direction of the changing at the middle of the bit, if going down, means bit 0, going up, means bit 1.   But it is easy to sample the middle of the first half of the bit, so it directly tells us what is the bit state, as we will see next in this text.

The Philips remote control sends 14 bits in sequence as you can see below.  (I am sorry to need to use more than your monitor width for the next picture, but it is to better view it).

(Figure 7)


You can see the 14 bits of the RC-5 system above. The RED bits are level "ON",  while Blue are "OFF".

The first two bits, #1 and #2,  are called ACG calibration. They are "ON" level, and serve to calibrate the IR Receivers Auto Gain Control.

In the Philips remotes, the bit #3 is the CHECK bit, every time you press a key at the remote, even pressing repeatedly the same key, this bit flips state.  This feature is interesting.  Suppose you pressed number "1" at the remote (trying to select channel 15 at TV) and holding it for 2 seconds, then  your other hand just blocks the InfraRed signal.  The TV would receive two trains of pulses, generated by your hand breaking a long train in two.  Other systems would understand transmission of two keys "1" selecting channel "11", but this do not happens in the Philips system.   This bit flips state every time you press a key, so blocking the signal with your hand doesn't change this bit, so the TV will understand that still the same key pressed.  To select channel "11" you should press key "1" really twice.

The next 5 bits, #4 to #8, are used for SYSTEM ADDRESS, or to identify which kind of device should execute the COMMAND bits.  For example, TV set uses ADDRESS ZERO.  Bit #8 is the Less Significant Bit.
 

SYSTEM ADDRESS EQUIPMENT
0 TV SET 1
1 TV SET 2
2 VIDEOTEXT
3 EXPANSION FOR TV 1 AND 2
4 LASER VIDEO PLAYER
5 VIDEO RECORDER 1 (VCR 1)
6 VIDEO RECORDER 2 (VCR 2)
7 RESERVED
8 SAT 1
9 EXPANSION FOR VCR 1 OR 2
10 SAT 2
11 RESERVED
12 CD VIDEO
13 RESERVED
14 CD PHOTO
15 RESERVED
16 AUDIO PREAMPLIFIER 1
17 RECEIVER / TUNER
18 TAPE / CASSETE RECORDER 
19 AUDIO PREAMPLIFIER 2
20 CD
21 AUDIO RACK
22 AUDIO SAT RECEIVER
23 DCC RECORDER
24 RESERVED
25 RESERVED
26 WRITABLE CD
26-31 RESERVED

The next 6 bits, #9 to #14, are used for COMMAND information to the device selected at the ADDRESS bits.   Bit #14 is the LESS SIGNIFICANT BIT, and it is last transmitted.

For example, STOP key uses COMMAND #54 (36h in hexadecimal), bits #9, #10, #12 and #13 should be ON, bits #11 and #14 should be OFF. 
 

COMMAND (in decimal) DESCRIPTION of FUNCTION
0-9 NUMERIC KEYS 0 - 9
12 STANDBY
13 MUTE
14 PRESETS
16 VOLUME UP
17 VOLUME DOWN
18 BRIGHTNESS  + 
19 BRIGHTNESS -
20 COLOR SATURATION +
21 COLOR SATURATION -
22 BASS UP 
23 BASS DOWN
24 TREBLE  + 
25 TREBLE -
26 BALANCE RIGHT
27 BALANCE LEFT
48 PAUSE 
50 FAST REVERSE
52 FAST FORWARD-
53 PLAY
54 STOP
55 RECORD 
63 SYSTEM SELECT
71 DIM LOCAL DISPLAY
77 LINEAR FUNCTION (+)
78 LINEAR FUNCTION (-)
80 STEP UP
81 STEP DOWN
82 MENU ON
83 MENU OFF
84 DISPLAY A/V SYS STATUS
85 STEP LEFT
86 STEP RIGHT
87 ACKNOWLEDGE
88 PIP ON/OFF
89 PIP SHIFT
90 PIP MAIN SWAP
91 STROBE ON/OFF
92 MULTI STROBE
93 MAIN FROZEN
94 3/9 MULTI SCAN
95 PIP SELECT
96 MOSAIC MULTI PIP
97 PICTURE DNR
98 MAIN STORED
99 PIP STROBE
100 RECALL MAIN PICTURE
101 PIP FREEZE
102 PIP STEP UP
103 PIP STEP DOWN
118 SUB MODE
119 OPTIONS BUS MODE
123 CONNECT
124 DISCONNECT

This system can be automated if using the chips:
SAA3049 or TDA3048 for receivers and SAA3006, SAA3010 or SAA3027 as transmitters.

 




To receive this signal using a microcontroller, follows the timing from the figure  7 above.   Note that the Infrared Receiver invert the bit signal, low level means bit ON.

During inactivity (no Infrared  present) the output of the Infrared receiver is UP (bit zero).

You can connect the IR receiver output to any input port pin or interrupt pin of your microcontroller, and keep polling it or prepare the interrupt routine to trigger your reading after the first low level sensed.

When you press a key at the remote, it transmits the train of pulses, and your microcontroller will receive bit #1 first.  It will be sensed right after the middle of the bit when it changes from high to low level to means bit "1".  This is the first time that your microcontroller will "see" the incoming IR signal.

You don't need to decode those first  two bits, not even the CHK bit (except if you want to control as the TV do and described above), so you can skip those 3 bits and start to receive the ADDRESS bits.  To do that, you need to skip 2.75 bits time, and you will be exactly at the middle of the right level of the first ADDRESS bit to be read (non inverted level).

Figure 8

So, upon sensing the first low level, your software should wait 4.752 milliseconds and then start to read the next 11 bits spaced 1.728ms each.   The first 5 bits are Address and the next 6 bits are  Command, logic correct level, LOW = 0, HIGH = 1.

To make sure your software is waiting the correct timing, you need to use a dual channel oscilloscope, and this procedure to adjust your software:

At your bit reading routine use an available microcontroller port pin and generate a fast pulse UP and DOWN,  then use one scope channel to display this pulse, and the other scope channel to show the incoming signal from the receiver.   Press and hold key number ZERO at the remote, and sync the scope to show a complete wave form, don't worry with timing. The fast 11 pulses should always be in place of those RED down arrows at the figure 8 above.  It means that the "bit reading" software routine will reading exactly in the middle of the correct bit level. 

TV-Silencer (Limat Graphics Inc)

Your software will need to have two timing delays, the first to wait 4.752ms and the second to wait 1.728ms.   Adjust the timing loop from the 4.752ms until the first fast pulse happens exactly as indicated above.  Then adjust the 1.728 ms timing delay in such way that the last fast pulse (#11)  bit reading happens exactly at the middle of the low part of the last bit (#14). 

Check all other bits and fast pulses, they should be all matching ok.   Small errors would be accepted since the reading would be happening in the middle of the bit, few errors for more or less is not a problem, but it is better to be the most possible in the middle of the low level of each bit.  This is why you should adjust your 1.728ms timing routine looking at the last data bit and fast pulse, if they match somehow ok, all the other bits should be ok too.

Remember that any other remote key will generate a different pattern and it can confuse you.  Use always key number ZERO for this software calibration.

Once you find the correct timing delays, you can replace the FAST pulse instructions with NOPS (check your chip instruction set to keep the same clock count wasted), or keep the fast pulse there just for fun, so you will be able to recheck it in case of problems.

Reading the 11 bits is easy.  Just shift them left into a 8 bits register and ignore the high order 2 bits #7 and #6 (AND 03Fh instruction), keep only the COMMAND last 6 bits... You will not want to decode the ADDRESS bits, are you?  The TV remote control will always send Address Zero, you know that, right? 

Here few examples of the complete waveform (14 bits) at the Receiver Output:

Values at the right are the command in hexadecimal
Red: AGC pulses (ON)
Blue: Check bit (flipping)
White: Address (00)
Green: Command

SAFETY

If you want to include some safety (recommended), check bits #7 and #6 for ZEROS, if it is a Philips TV remote.   You can also not use the 4.752ms delay, instead, wait only 3/4 of a bit time, and then start to read from the bit #2.  You will suppose the first one was a "1" and the second should be a "1" too, if not, discard  them, wait 60ms and activate reception again, you should sync correctly at the beginning of the next train of pulses.  But even this way, you could read wrongly a "1" bit followed by another if the reading start anywhere in the middle of the train. 

To make sure your controller is never starting to read the train in the middle, you can discard the first reading always after a long silence (half second or more), so you will make sure that the second reading will be in sync.  To do that, after idling for more than half second, enter in a special sync routine and upon sensing the first LOW level bit (can be the real first or not), wait 60ms and jump to the real receive routine and start to monitor the Receiver output again.  It means that the first train will be used just to make your receive routine to engage in a correct timing to read the second train of pulses. 

Remember that there is a delay of 105ms between pulse trains, so doesn't matter which LOW bit you sensed, waiting 60ms will put your reception routine in the middle of the silence between pulse trains, allowing it to sync  at the first bit of the next train of pulses.


 


The following circuit and code were used in one of our equipment, using a remote control for mechanical positioning.  The At89C2051 were selected by fast coding and low cost.  Today probably I would use an small Tinny AVR unit. The software listing below was stripped from other non essential coding, necessary to our machine, but not necessary here.


8051  ASSEMBLY  CODE

;  лллллллм     млллллм            лллллллл
;  лл    плл   ллп    пл           лл
;  лл    млл   лл                  лл
;  лллллллл    лл                  лллллллм
;  лл   лл     лл                        плл
;  лл    лл    ллм    мл           ллм   млл
;  лл     лл    плллллп             плллллп
;
; SOFTWARE FOR AT89C2051 TO DECODE PHILIPS REMOTE CONTROL
; RC-5 CODIFICATION - INFRA-RED RECEIVER LT1029-ND DIGIKEY
; CLIPPED PARTS FROM THE ORIGINAL SOURCE TEXT:
;   A) TRANSMITTER
;   B) SELECTION FOR PHILIPS / FC1 - (WORKING PHILIPS)
; AT89C2051 RUNNING AT 2MhZ <== IMPORTANT
; WAGNER LIPNHARSKI - NOVEMBER 1999 - WAGNER@USTR.NET
; UST RESEARCH INC. - ORLANDO, FL - WWW.USTR.NET
;
$MOD51
$NOPAGING
$LIST
;
; PIN 11 (P37) : 0 = RECEIVER CIRCUIT
;              : 1 = TRANSMITTER CIRCUIT
;
; PIN  2 (P30) : 1 = RECEIVER DECODES PHILIPS REMOTE
;              : 0 = RECEIVER DECODES FC1 REMOTE
;
; PIN 12 (P10) : PULLED UP = FC1 CODE TRANSMITTER
;              : GROUND    = PHILIPS CODE TRANSMITTER
;
; RECEIVER CONFIGURATION:
; -----------------------
; PIN 7 (P33) INPUT SIGNAL FROM IR RECEIVER
; PINS 12-19 DECODER OUTPUT (DRIVE TO GROUND)
; PIN 11 TO GROUND.
; CLOCK CERAMIC RESSONATOR 2MhZ
; RESET CAP 1uF TO +VCC
; PIN 9 (P35) CAN BE USED TO LITE A LED WHEN RECEIVING VALID IR
; PIN 8 (P34) SCOPE GATE TIME (SOFTWARE TIMMING ADJUSTMENT)
;
; ---___---___------______---___---___--- PIN 7 P33 IRDATA
; _|_____|_____|_____|_____|_____|_____|_ PIN 8 P34 SCOPE READ GATE TIME
;
; --__  1 BIT
;             RX DATA
; __--  0 BIT
;

; TRANSMITTER CONFIGURATION:
; --------------------------
; PINS 2,3,6,7,8,9 & 11 TIED TOGETHER TO DRIVE IR LED
; PINS 16-19 KEYBOARD MATRIX DRIVE (4 PINS)
; PINS 14 & 15 KEYBOARD MATRIX RETURN WITH PULL UP
; CRYSTAL 6MHZ
; RESET CONTROLLED BY FET BS110, DIODES FROM KEYBOARD.
; PIN 12 GOES TO GROUND WHEN IN POWER OFF

             ;------------------
             ; Receiver
             ;------------------
Led          BIT   0B5h   ; P3.5
IrInput      BIT   0B3h   ; P3.3
Scope        BIT   0B4h   ; P3.4
RxTx         BIT   0B7h   ; P3.7 ; Grounded if Receiver/High if TX
             ;------------------
             ; Transmitter
             ;------------------
TXLED        EQU   P3     ; FF = Off, 00 = On
KO1          Bit   097h   ; P1.7 Keyboard Output
KO2          Bit   096h   ; P1.6
KO3          Bit   095h   ; P1.5
KO4          Bit   094h   ; P1.4
KI1          Bit   093h   ; P1.3 Keyboard Input
KI2          Bit   092h   ; P1.2

IRDATA      DATA   010H   ; Memory to store IR code received

;======================================;
;
; P H I L I P S     R E M O T E
; CODE "10" AT AV6 UNIVERSAL PROGRAMMABLE REMOTE CONTROL
;
;======================================;
ORG 00H
MAIN:        Mov  SP,#SPVALUE          ;

PH0:         Mov  P1,#0FFh             ; Reset Decoder Output High
             Setb LED                  ; Turn off IR Indicator
             ;                         ;
PH1:         Mov  4,#022               ; 2MHz
             Mov  5,#000h              ; 2MHz Time loop
PH2:         Jnb  IrInput,PH3          ; Wait for Incomming IR (first low)
             Djnz 5,PH2                ; This time loop is to keep the last
             Djnz 4,PH2                ; ..pressed key available at P1 for few
             Jmp  PH0                  ; ..time in case you press it again
                                       ; ..and avoid glitches at P1.
             ;-------------------------;
PH3:         Clr  A                    ; IR Receiver First Low level.
             Clr  Led                  ; Lite IR Indicator
             ;                         ;
             Mov  2,#110               ; Time Loop (3/4 bit time)
             Djnz 2,$                  ; Waste Time to sync second bit
             ;                         ; 2MHz = 1.296ms
             Mov  B,#7                 ;
PH4:         Setb Scope                ; Scope Gate Indicator Pulse UP
             Mov  C,IrInput            ; Shift IR state to Carry bit
             Clr  Scope                ; Scope Gate Indicator Pulse Down
             Rlc  A                    ; Insert LEFT Carry Bit into A Reg
             ;                         ;
             Mov  2,#145               ; Waste time for next BIT
             Djnz 2,$                  ; 2MHz clock, 1.728ms
             ;                         ;
             Djnz B,PH4                ; Rotate 7 bits into A
             ;                         ; AGC#2, CHKbit, ADDRESS field (5 bits)
             ;-------------------------;
             Anl  A,#0F7h              ; Cut off CHECK Bit (Flipping bit)
             Cjne A,#40h,PH5           ; 10h means second AGC UP & Address 00
             ;                         ; Not 10h?, wrong sync, go again (PH5)
             ;-------------------------;
             Mov  B,#6                 ; Will Get the COMMAND field
PH4A:        Setb Scope                ; Scope Gate Indicator Pulse UP
             Mov  C,IrInput            ; Shift IR state into Carry bit
             Clr  Scope                ; Scope Gate Indicator Pulse Down
             Rlc  A                    ; Insert LEFT carry bit into A Reg
             ;                         ;
             Mov  2,#145               ; Waste time for next BIT
             Djnz 2,$                  ; 2MHZ clock = 1.728ms
             ;                         ;
             Djnz B,PH4A               ; Rotate 8 bits into A (Command)
             ;                         ; Here A holds Command bits
             ;-------------------------;
             Mov  IRData,A             ; Save Command at IRData memory
             Cjne A,#25h,$+3           ; Is Command >=25h
             Jnc  PH5                  ; Yes? Wrong everything, go again PH5
             ;                         ;
             Call PH6                  ; Go get Conversion at Table
             Cjne A,#0FFh,PH4B         ; If conversion <> FF, is valid.
             Jmp  PH5                  ; ..Not Expected Command. go again PH5
             ;                         ;
PH4B:        Mov  P1,A                 ; Valid Command is post at P1 Port
             Jmp  PH1                  ; Job done, go wait next pulse train.
             ;                         ;
             ;-------------------------;
PH5:         Mov  3,#8                 ; 2MHz
             Mov  2,#112               ; Wait 15 bit time
PH5A:        Djnz 2,$                  ; Wasting time to sync ok next train
             Djnz 3,PH5A               ;
             Jmp  PH0                  ; Go back and wait for next train.
             ;-------------------------;
PH6:         Inc  A                    ; Table conversion, Inc skip RET
             Movc A,@A+PC              ; Point to TABLE + Value at A (1-255)
             Ret                       ;
             ;-------------------------;
             ;  The following table bit values at the first column, means
             ;  the translation from remote control key to the value to be
             ;  be post at P1.  The program ignores values of "FF".
             ;  Change those bits according to your needs.
             ;
             ;  Bit #7 is "0" when a valid key is pressed, otherwise is "1"
             ;  It can be used to recognize values as key "zero" pressed,
             ;  when all bits UP means command ZERO.
             ;
             ;  This TV remote uses only Address = "00"
             ;
             ;    PHILIPS TV REMOTE CONTROL DECODING
             ;
             ;    VALUE TO P1   REMOTE KEY   COMMAND CODE FIELD (HEX)
             ;    -----------   ----------   ------------------------
TABLE:       DB   01111111b    ; 0         ; 0
             DB   01111110b    ; 1         ; 1
             DB   01111101b    ; 2         ; 2
             DB   01111100b    ; 3         ; 3
             DB   01111011b    ; 4         ; 4
             DB   01111010b    ; 5         ; 5
             DB   01111001b    ; 6         ; 6
             DB   01111000b    ; 7         ; 7
             DB   01110111b    ; 8         ; 8
             DB   01110110b    ; 9         ; 9
             DB   11111111b    ;           ; A
             DB   11111111b    ;           ; B
             DB   01110011b    ; ON/OFF    ; C
             DB   01110010b    ; MUTE      ; D
             DB   01110001b    ; PP        ; E
             DB   01110000b    ; OSD       ; F
             DB   01101111b    ; Volume+   ; 10
             DB   01101110b    ; Volume-   ; 11
             DB   01101101b    ; Bright+   ; 12
             DB   01101100b    ; Bright-   ; 13
             DB   01101011b    ; Color+    ; 14
             DB   01111010b    ; Color-    ; 15
             DB   11111111b    ;           ; 16
             DB   11111111b    ;           ; 17
             DB   11111111b    ;           ; 18
             DB   11111111b    ;           ; 19
             DB   11111111b    ;           ; 1A
             DB   11111111b    ;           ; 1B
             DB   01100011b    ; Contrast+ ; 1C
             DB   01100010b    ; Contrast- ; 1D
             DB   11111111b    ;           ; 1E
             DB   11111111b    ;           ; 1F
             DB   01011111b    ; Program+  ; 20
             DB   01011110b    ; Program-  ; 21
             DB   11111111b    ;           ; 22
             DB   11111111b    ;           ; 23
             DB   01011011b    ; Timer     ; 24
             DB   01010111b    ; Special 1 ; 25
             DB   01000001b    ; Special 2 ; 26
             DB   01000111b    ; Special 3 ; 27
             DB   01001110b    ; Special 4 ; 28
             DB   01000101b    ; Special 5 ; 29
             DB   01010010b    ; Special 6 ; 2A
END

 


Wagner Lipnharski (wagner@ustr.net)
Last Edited: Nov/2003



Domain Registrations starting at $9.98*

CompUSA

icon

CompUSA Best sellers

BANNERS EFORCHINA

37% off Deluxe Hosting- Get 12 months for price of Economy

CompUSA

When your computer needs a BOOST - 4AllMemory.com! - 125x125

GeekZones

electronics 125x125

CompUSA